The InvisiGARD Paint and Headlight Protection product is a simple way to provide ultimate protection for your bike's painted and headlamp surfaces. With the comprehensive written instructions as well as detailed photos and informative videos, you'll see that just about anyone can install this product with ease.





While instructions shown below reference our Fender Protection Kit for the D.F.T. Trike FL Smoothie part #IPP-DFT-1000, techniques shown herein will apply for other kits we have available on our website.

Written Instructions

Please consider the environment before you print these instructions.

The kit ordered will include a squeegee, a sheet of InvisiGARD precut pieces and information on how to view our detailed and comprehensive online instructions.

Installation supplies you'll need to gather include two (2) spray bottles, paper towels, denatured alcohol (or methyl hydrate), baby shampoo, scissors (or utility knife) and squeegee. We provide the squeegee with the kit.

The reason we suggest baby shampoo is that it contains less detergents than other liquid soap products.



As an alternative to denatured alcohol (or methyl hydrate) & baby shampoo, try Rapid Tac!

Available in various sizes, this environmentally friendly product can be used as a cleaner, Positioning Solution and Mounting Solution - All in One!

Best of all Rapid Tac stimulates the adhesive to bond in approximately ninety seconds, even in adverse climates such as extreme hot or cold. It will not cause bubbles so there's no returning to poke holes in your work either.

It's what we now use for our local installations!


A note about Installation Conditions

PAINTED SURFACES AND InvisiGARD PAINT PROTECTION PRODUCT MUST BE AT OR SLIGHTLY ABOVE ROOM TEMPERATURE FOR INSTALLATION. The key to maximum adhesion is that installation surfaces and InvisiGARD product are at or slightly above room temperature (60-90 degrees F). USE CAUTION NOT TO OVERHEAT SURFACE OR InvisiGARD MATERIAL.

First, using a clean, lint-free wipe (i.e. untreated paper towel), thoroughly clean all areas of installation with an adhesive remover to remove waxes, silicones, etc. Second, clean surfaces again with glass cleaner (avoid cleaners containing ammonia and/or soaps). Cleaning with DENATURED ALCOHOL will suffice for both previous steps (NOTE: DO NOT USE ISOPROPYL/RUBBING ALCOHOL). Rubbing surface with fingers should yield a "squeaky clean" feeling & sound.

Note: While denatured alcohol is recommended for use in this surface cleaning step, take care not to allow full-strength denatured alcohol to touch the InvisiGARD product. The aggressive nature of this chemical may haze or melt the glossy surface.

A note about Surface Cleanliness

The prior use of synthetic protectants and silicones (i.e. Armorall, Son of a Gun, Rainex, etc.) on the substrate can result in adhesive difficulties. Therefore, special substrate cleaning with a silicone removal agent (i.e. 3M #08984 General Purpose Adhesive Cleaner, Denatured Alcohol, etc.) may be required, perhaps repeatedly. Final cleaning with DENATURED ALCOHOL is recommended with thorough drying of the surface. Clean all surfaces until all slick feel on the substrate is gone. Always test any cleaner on inconspicuous area first for any reactions to surface finishes.

Pre-fitting is suggested. As shown above, you'll be receiving the InvisiGARD product on a sheet. Carefully trim backing sheet around each individual piece with a scissors or utility knife (be careful not to cut into the InvisiGARD). Once trimmed, "dry fit" each piece to get an idea of how they are to be installed. Due to the nature of the InvisiGARD product, especially so for Trike Fenders, some of the pieces may appear smaller or shorter than the actual area of installation, however you'll be stretching them into place in the installation process.

Mix a spray bottle full of Positioning Solution using just a few drops of baby shampoo in a bottle full of warm water. Positioning Solution will help you "slide" the InvisiGARD into place on the larger pieces such as the one shown. Smaller pieces may not require this solution and can simply be applied with Mounting Solution as described below.

Once solution is mixed, spray area of installation liberally.

Installation Tip:

To reduce the possibility of unwanted fingerprints in the adhesive system of the InvisiGARD, keep hands wet with Positioning or Mounting solution.

After you spray the area, peel the InvisiGARD from the backing paper and spray the adhesive side with the solution.

Once both contact surfaces are sprayed with solution, "slide" the piece of InvisiGARD into place. Remember that the piece may be smaller or shorter than the actual area.

For Trike Fender pieces, "slide" the piece to approximately 1/8" from the bottom edge of the Fender, keeping in mind that you'll be stretching the InvisiGARD into place in the final step.

When the InvisiGARD is in place, set a "hinge" point by squeegeeing the piece at the bottom of the Fender as shown. When using a squeegee, keep in mind that you are making an effort to force air and solution out from between the two contact surfaces. Spraying a little solution on the outside of the InvisiGARD will allow the squeegee to slide over the surface easier.

Once the "hinge" point is set, lift the top part of the piece off the Fender and spray both the area and the adhesive side of the InvisiGARD thoroughly with Mounting Solution. Mounting solution consists of a 50/50 mixture of warm water and denatured alcohol.

Remember, spraying a little solution on the outside of the InvisiGARD will allow the squeegee to slide over the surface easier.

With the piece on the Fender, go ahead and s-t-r-e-t-c-h it up into place while at the same time working the air and solution out with a squeegee right up the center from the bottom.

When designing Fender pieces for Trikes, we tend to shrink them approximately 3/4" in height so that when installing the piece, the "fingers" or "puckers" found at the sides of the protector disappear when it is stretched up as required.

Our InvisiGARD material consists of a urethane film that is very stretchable. Taking advantage of this property, most irregularly shaped and curved surfaces such as the one shown require stretching into proper placement.

With the center area of the protector set, proceed to squeegee the sides.

Please Note: Installed crooked? Don't despair. InvisiGARD can be lifted and reset - even if you squeegeed it down. Just remember to apply more Mounting Solution prior to resetting with a squeegee.

Simple As That!

ALLOW ADHESIVE TO SET OR CURE FOR AT LEAST 72 HOURS BEFORE WASHING THE SURFACES. As a rule, any visible grainy images in the film (after thoroughly rubbing out the film) will cure out within that 72 hour period. MANUFACTURER AND/OR DISTRIBUTOR CANNOT BE HELD RESPONSIBLE FOR IMPROPER INSTALLATION.


The manufacturer and seller of this product believe this product to be suitable and to have the necessary characteristics to serve itís intended purpose based upon the technical information, testing and statements herein, which we believe to be reliable, however, the completeness and accuracy thereof is not guaranteed. Manufacturer and seller make no warranties, expressed or implied, including implied warranties of merchantability for this product and fitness for any purpose. Manufacturer's and sellerís sole obligation shall be the replacement of that portion of this product proven to be defective. Before using this product, user shall examine and determine the suitability of this product for user's intended purpose and assumes all risk and liability whatsoever related to its use. Neither Manufacturer NOR SELLER SHALL BE LIABLE, EITHER IN CONTRACT OR TORT for THE USE Of, MISUSE, OR INABILITY TO USE THIS PRODUCT. THIS SHALL COVER ANY LOSS OR DAMAGE, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL RELATED TO THE USE Of THIS PRODUCT. No recommendation or statement outside of this notice shall have any effect or force except in writing signed by authorized officers or manufacturer and seller.

As always, if you have any questions feel free to e-mail us. We're here to serve.   Thanks!
Need to contact us? Simply email us at

Copyright © 2009 [Auto Trim DESIGN]. All rights reserved. InvisiGARD is a registered trademark of Auto Trim DESIGN of Northeast Wisconsin, Inc.